5454 H22 and H32 Sheet & Plate Grade - Aluminium

Range Enquiry

To enquire about our range or your specific requirements, please contact your local service centre.

Related Specifications

Alloy 5454 corresponds to the following standard designations and specifications but may not be a direct equivalent:

A5454
ISO Al Mg3MN
Al 2.7Mg 0.8Mn Cr

Temper Types

The most common tempers for 5454 aluminium are shown below:

H22
O
H111
H32

Properties

Chemical Composition

Chemical Element	% Present
Manganese (Mn)	0.50 - 1.00
Iron (Fe)	0.00 - 0.40
Magnesium (Mg)	2.40 - 3.00
Silicon (Si)	0.00 - 0.25
Chromium (Cr)	0.05 - 0.20
Titanium (Ti)	0.00 - 0.20
Zinc (Zn)	0.00 - 0.25
Copper (Cu)	0.00 - 0.10
Other (Each)	0.00 - 0.05
Others (Total)	0.00 - 0.15
Aluminium (Al)	Balance

Mechanical Property	Value
Proof Stress	180 Min MPa
Tensile Strength	250 - 305 MPa
Hardness Brinell	74 HB

General Physical Properties

Physical Property	Value
Density	2.69 g/cm³
Melting Point	645 °C
Thermal Expansion	23.6 x 10^-6/K
Modulus of Elasticity	70.5 GPa
Thermal Conductivity	135 W/m.K
Electrical Resistivity	34 % IACS

Applications

Road transport bodybuilding
Chemical and process plant
Pressure vessels, containers, boilers
Cryogenics
Marine & offshore
Pylons, poles & masts

Characteristics

Medium to high strength
Strengthened by cold working
Similar to alloy 5754 with good strength in the temperature range 65 to 170 degrees centigrade.
High fatigue strength
It is not suitable for complex or fine extrusions
Good formability in softer tempers
Good weldability

Additional Information

Weldability

Find your local Service Centre

Experienced multi-product specialists
In-house state of the art processing facilities
Large fleet of bespoke delivery vehicles

Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon. Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed S online) and manufacturers' data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources. Material supplied by the Company may vary significantly from this data but will conform to all relevant and applicable standards. As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied. Advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. All transactions are subject to the Company's current Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.

Aluminium, Commercial Alloy5454 H22 and H32 Sheet & Plate

Medium-high strength aluminium alloy with exceptional corrosion resistance.

Range Enquiry

Related Specifications

Temper Types

Properties

Alloy 5454

BS EN 573-3

Sheet 0.2mm to 6.0mm thick

BS EN 485-2

Applications

Characteristics

Additional Information

Find your local Service Centre