Related Specifications
Aluminium alloy 6262 also corresponds to the following standard designations and specifications but may not be a direct equivalent:
- AA6262
- Al 1.0Mg 0.6Si Pb
- A96262
PLEASE NOTE: Due to European Environmental Protection Directives:
- 2000/53/CE-ELV – For the automotive sector
- 2002/95/CE-RoHS – For the electrical and electronics sector
This alloy has been replaced by Alloy 6026 which has a lower lead content.
Temper Types
The most common tempers for 6262 aluminium are:
- T9
- T6
Properties
Chemical Composition
Alloy 6262
BS EN 573-3
Chemical Element | % Present |
---|---|
Manganese (Mn) | 0.00 - 0.15 |
Iron (Fe) | 0.00 - 0.70 |
Magnesium (Mg) | 0.80 - 1.20 |
Silicon (Si) | 0.40 - 0.80 |
Zinc (Zn) | 0.00 - 0.25 |
Titanium (Ti) | 0.00 - 0.15 |
Chromium (Cr) | 0.04 - 0.14 |
Copper (Cu) | 0.15 - 1.40 |
Bismuth (Bi) | 0.40 - 0.70 |
Lead (Pb) | 0.40 - 0.70 |
Other (Each) | 0.00 - 0.05 |
Others (Total) | 0.00 - 0.15 |
Aluminium (Al) | Balance |
Mechanical Properties
Rod & Bar Up to 200mm Dia. & A/F
BS EN 755-2
Mechanical Property | Value |
---|---|
Proof Stress | 240 Min MPa |
Tensile Strength | 260 Min MPa |
Elongation A50 mm | 8 Min % |
Hardness Brinell | 75 HB |
Elongation A | 10 Min % |
Tube Up to 25mm Wall Thickness
BS EN 755-2
Mechanical Property | Value |
---|---|
Proof Stress | 240 Min MPa |
Tensile Strength | 260 Min MPa |
Elongation A50 mm | 8 Min % |
Hardness Brinell | 75 HB |
Elongation A | 10 Min % |
Profiles Up to 25mm Wall Thickness
BS EN 755-2
Mechanical Property | Value |
---|---|
Proof Stress | 240 Min MPa |
Tensile Strength | 260 Min MPa |
Elongation A50 mm | 8 Min % |
Hardness Brinell | 75 HB |
Elongation A | 10 Min % |
General Physical Properties
Physical Property | Value |
---|---|
Density | 2.71 g/cm³ |
Melting Point | 582 °C |
Thermal Expansion | 23.4 x 10-6/K |
Modulus of Elasticity | 68.3 GPa |
Thermal Conductivity | 172 W/m.K |
Electrical Resistivity | 0.039 x 10-6 Ω .m |
Applications
- Screw machine products
- Camera parts
- Nuts
- Couplings
- Marine fittings
- Decorative hardware and appliance fittings
- Hinge pins
- Oil line fittings
- Valves and valve parts
Characteristics
- Very good corrosion resistance
- Very good strength
- Excellent machinability and surface finish due to additions of bismuth
- High-speed steel or carbide tooling can be used to obtain smooth finishes. Heavy cutting requires oil lubricant but light cutting can be done dry
- Alloy 6262 can be used in place of 2011 when higher corrosion resistance and better anodising response is required
Additional Information
Weldability
Alloy 6262 is readily weldable by all commercial methods and can also be brazed.
Process | Rating |
---|---|
Weldability - Gas | Excellent |
Weldability - Arc | Excellent |
Weldability - Resistance | Excellent |
Brazability | Excellent |
Fabrication
Process | Rating |
---|---|
Workability - Cold | Poor |
Machinability | Excellent |